1, BC01 / BC-02, BX-2, BC20 ink cartridges
First determine the nozzle is good or bad, and then use the ink package attached to the small hook on the cartridge to pull out the small plug, the ink bottle probe into the cartridge to fill, after the small plug to re-plug in situ can.
2, BC03 / BX-3 ink cartridges;
First determine the nozzle is good or bad, and then use the ink inside the package with the blue hard drive to push the ball on the surface of the cartridge pressure, the ink bottle probe into the cartridge to fill, after the use of ink packaging with Of the soft plug or ball will seal the ink mouth, and then posted a layer of transparent plastic can be.
3, BC05 / 06 ink cartridges
Filling method BC01 / 02 the same. Note that 05 is the color ink cartridges, before filling the first use of three clean toothpicks were probing into the three water injection, remove the observed toothpick stained on the color, select the appropriate color canon ink filling.
4, BCI10BK / 11BK / 11C / 21BK / 21C and other ink cartridges
When you add ink only need to reverse the cartridge, the corresponding ink will slowly drop into the ink can be.
5, BC-61 cf400x;
This cartridge is three-color, please fill in the correct filling hole to ensure that the correct color, and then reverse the ink cartridges placed in the newspaper, the ink slowly into the ink hole, when the ink is full, The excess ink will overflow from the vent surface of the cartridge label surface, immediately remove the overflow ink, reverse the ink cartridge, the ink may drip from the ink hole, remove the ink to confirm the ink drip.
Precautions:
1, 01/02/03/05/06 and other ink cartridges when filling, the ink must be filled (to ensure that the air pressure within the cartridge balance) but not excessive, even occasionally will cause leakage of ink, resulting in unnecessary waste.
2, once the cartridge is used up, should be promptly filled with ink (or timely replacement of ink cartridges), so as to avoid prolonged exposure to the nozzle, causing nozzle clogging in the air.
3, The use of drip filling method, will not damage the cartridge sponge, fill the number of times more than the use of needle filling BC-01/02/03/05/05, BCI-20, BJI -201, BJI-642/643 cartridge.
1, HP printer does not feed fault repair hp printer cartridges has a certain requirement for paper, 40 grams of the following paper, easy to use in the heating roller, if forced to pull out the paper, may make the cardboard detection sensor off, will make the paper break, the remaining part of the more Hard to take out. After the front cover of the printer is opened, there is a green button on the left side of the printer, pushing upwards, and you can easily remove the jam. If you do not take the paper, it is best to ask the professional maintenance personnel to open the case to remove the paper. More than 100 grams of paper because the paper is too thick, rubbing paper and paper between the friction is too large, easy to cause the pickup roller premature aging, there is no paper phenomenon. The general solution is to open the printer, the pickup roller for nap, artificially increase its friction. But this method is not effective, can not take three months, then they will appear the same failure. There is also a way to replace the pickup roller, but must go to the HP special service center to go. I found in the maintenance process, if the pickup roller at the same time, on both sides of the pickup wheel on the plastic control wheel evenly coated with a lap grease. In this way, can be used for more than a year. If there is no paper feeding phenomenon, as long as the grease can be coated with grease.
2, HP printer heating fault repair hp 201x printer with a heating plate for heating, because the heating film is very thin, sometimes because the cardboard will cause serious heatsink pieces, sometimes heating the film below the temperature sensor premature aging, the printer appears three lights full, without any action. At this time you can replace the heater. The heated part of the HP6L can be replaced as a whole, or it can be replaced in part (heating plate, heating film, roller). I encountered in the maintenance process must be replaced by the roller, the reason is not natural roller aging, often human factors - mostly cardboard, with a child, knife and other sharp objects in the process of taking the paper, the glue Roller surface scratches, causing ruggedness.
3, printing is not normal
Sometimes the printer can print, but not normal. If there is somewhere clear, some places light or some places there are horizontal lines and other phenomena related to the printer cartridge, the specific reference to the printer manual. If you only print a line, such as "@ PCL5" and other words, often the printer driver is not correct, select the correct driver can be. When printing characters do not understand, only one line or two or three lines, you should consider whether the print cable is loose, print the cable is in line with the standard, whether too long. When printing cable over 3 meters, prone to print is not normal. If the characters can also print characters, but there are individual characters missing (Chinese characters or English), you should consider whether the host interface circuit is damaged. At this point the printer should be able to print properly in other hosts.
1, HP printer does not feed fault repair hp printer cartridges has a certain requirement for paper, 40 grams of the following paper, easy to use in the heating roller, if forced to pull out the paper, may make the cardboard detection sensor off, will make the paper break, the remaining part of the more Hard to take out. After the front cover of the printer is opened, there is a green button on the left side of the printer, pushing upwards, and you can easily remove the jam. If you do not take the paper, it is best to ask the professional maintenance personnel to open the case to remove the paper. More than 100 grams of paper because the paper is too thick, rubbing paper and paper between the friction is too large, easy to cause the pickup roller premature aging, there is no paper phenomenon. The general solution is to open the printer, the pickup roller for nap, artificially increase its friction. But this method is not effective, can not take three months, then they will appear the same failure. There is also a way to replace the pickup roller, but must go to the HP special service center to go. I found in the maintenance process, if the pickup roller at the same time, on both sides of the pickup wheel on the plastic control wheel evenly coated with a lap grease. In this way, can be used for more than a year. If there is no paper feeding phenomenon, as long as the grease can be coated with grease.
2, HP printer heating fault repair hp 201x printer with a heating plate for heating, because the heating film is very thin, sometimes because the cardboard will cause serious heatsink pieces, sometimes heating the film below the temperature sensor premature aging, the printer appears three lights full, without any action. At this time you can replace the heater. The heated part of the HP6L can be replaced as a whole, or it can be replaced in part (heating plate, heating film, roller). I encountered in the maintenance process must be replaced by the roller, the reason is not natural roller aging, often human factors - mostly cardboard, with a child, knife and other sharp objects in the process of taking the paper, the glue Roller surface scratches, causing ruggedness.
3, printing is not normal
Sometimes the printer can print, but not normal. If there is somewhere clear, some places light or some places there are horizontal lines and other phenomena related to the printer cartridge, the specific reference to the printer manual. If you only print a line, such as "@ PCL5" and other words, often the printer driver is not correct, select the correct driver can be. When printing characters do not understand, only one line or two or three lines, you should consider whether the print cable is loose, print the cable is in line with the standard, whether too long. When printing cable over 3 meters, prone to print is not normal. If the characters can also print characters, but there are individual characters missing (Chinese characters or English), you should consider whether the host interface circuit is damaged. At this point the printer should be able to print properly in other hosts.
Users who use laser printers know that when using the toner cartridge will always meet the toner powder leakage thing. So what is the cause of toner leakage?
Toner powder leakage, in addition to shell damage, usually during transport or because some customers in the course of the use of the cartridge within the powder powder powder reasons. The solution is very simple, as long as the brother toner along the direction of a few laps on it.
How does the laser printer leak? Toner powder leakage how to do?
Print documents and toners at the same time appear 1 cm above the same wide vertical underworld, the general customer also think that is leaking powder: This is a scraper out of the problem, resulting in stick powder on the powder is not clean.
Printed on the file appears in the vertical thin black Road: usually scraper and scraper on the edge of the small blade stick to dirty things or shredded paper.
Print the file appears in the horizontal underworld: usually the cartridge inside the magnetic stick powder, along the turn a few laps on it.
If the printed documents appear obvious bottom ash: usually toner core or brother toner is a problem.
Print the file color uneven, well-known white Road: from the outside to see the magnetic stick can not see the brother tn 660, if you see some places on the magnetic stick powder, some places no powder, indicating that the toner cartridge to run out.
If the printer to play a white one: first check the printer has no problem, if there is no problem, it shows the cartridge in the assembly of a problem.
Meet the problem in a timely manner to solve the US state lease for the purpose of customer service. If you have any other technical questions please contact us promptly.
The laser printer receives the data sent by the computer over the cable, and the processor processes the data into a signal group of similar data tables that can drive the print engine action. Next, the laser printer starts working. The outer surface of the toner is uniformly charged with a negative charge, whenever the printer to play a black spot, it will be a small laser diode light, laser diode laser through a series of mirrors to reach the toner on the organic photosensitive material, make the point into a conductor.
Nowadays, ink cartridges becomes more and more important in our work, but do you know how to add toner to printers?
Old drums are different, the same toner to print out the different quality of the situation. So before filling the powder carefully check the old drum in all aspects of the situation, can only print out the ideal quality.
One. Please print the test page with the old drum. If the black spots or stains appear regularly, then the drum member problem, find out defective parts replaced after the drum apart, normally occurring case where the photosensitive drum is damaged.
Please check if your drum is damp. If the cartridge has just come out from the printer, there is no such problem. What is meant here is that the cartridge has been removed from the printer for some time, during which if you place the wall or other non-dry place, the possibility of damp is very large. Users are often easy to ignore this problem.
Then the user can be judged by the page hit detector old drum damp, if the detected page appears bottom ash, or a stick found photosensitive drum tn660 toner scratch can not afford, then this is damp the drum, the drum may be considered apart and Old, Blowing 5-10 minutes with hair dryer. If the damp situation is more serious temporarily not powder.
Three. If your old drum is the first time to fill the powder, it must be completely clean dry powder warehouse and waste toner box, if the second powder still use the same brand of toner is only clean the waste toner box can be. It is important to note that each time the powder must be cleaned.
Four. After the drum is removed, please turn the magnetic roller to see if the powder is uniform and whether it is scratched. If the powder is not even or the circle is present, it will damage the magnetic roller or inner scraper.
Five. If you buy a lot of toner, please put the temporary excess toner stored in low temperature dry place, do not want to avoid the sun and high temperature, otherwise it may be due to condensation and can not be used.
If you need purchase some printers, welcome to V4INK, here will support you good quality and best price. Please come and have a try.
Nowadays, ink cartridges becomes more and more important in our work, but do you know how to add toner to printers?
Old drums are different, the same toner to print out the different quality of the situation. So before filling the powder carefully check the old drum in all aspects of the situation, can only print out the ideal quality.
One. Please print the test page with the old drum. If the black spots or stains appear regularly, then the drum member problem, find out defective parts replaced after the drum apart, normally occurring case where the photosensitive drum is damaged.
Please check if your drum is damp. If the cartridge has just come out from the printer, there is no such problem. What is meant here is that the cartridge has been removed from the printer for some time, during which if you place the wall or other non-dry place, the possibility of damp is very large. Users are often easy to ignore this problem.
Then the user can be judged by the page hit detector old drum damp, if the detected page appears bottom ash, or a stick found photosensitive drum tn660 toner scratch can not afford, then this is damp the drum, the drum may be considered apart and Old, Blowing 5-10 minutes with hair dryer. If the damp situation is more serious temporarily not powder.
Three. If your old drum is the first time to fill the powder, it must be completely clean dry powder warehouse and waste toner box, if the second powder still use the same brand of toner is only clean the waste toner box can be. It is important to note that each time the powder must be cleaned.
Four. After the drum is removed, please turn the magnetic roller to see if the powder is uniform and whether it is scratched. If the powder is not even or the circle is present, it will damage the magnetic roller or inner scraper.
Five. If you buy a lot of toner, please put the temporary excess toner stored in low temperature dry place, do not want to avoid the sun and high temperature, otherwise it may be due to condensation and can not be used.
If you need purchase some printers, welcome to V4INK, here will support you good quality and best price. Please come and have a try.
Only about 15% to 20% of toner cartridge and printer ink cartridges are recycled every year. The majority of them end up in landfills and takes thousands of years to break down and eventually decompose. The toxic chemicals present in them spreads into the soil and waterways and pollutes the environment. Also, manufacturing new cartridges every time leads to loss of precious natural resources and causes global warming.
Every year, more than 375 million of empty toner cartridges and ink cartridges are dumped in landfills or in incinerators, creating a massive wastage.
The production of a toner cartridge requires about 2 quarts of petroleum. More than 200 million liters of petroleum is consumed in the manufacturing process of printing cartridges in North America alone, with most of the cartridges ending up in landfill once they are used.
Even though it is possible to recycle each cartridge, approximately 50% of all toner cartridge and 70% of ink cartridges are still not recycled every year, thus, adding to the already increasing electronic waste. Research suggests that if all ink cartridges are recycled, approximately 11 million gallons of oil can be saved in just seven months.
It takes around 450 to 1000 years for the engineering grade polymer present in the plastics of printer cartridges to decompose and break down. Moreover, ink cartridges also leak ink which ends up in polluting the overall environment including soil and waterways.
It is possible to reuse printer cartridges up to 15 times before they become completely unusable while averaging between 5-7 refills.
Using remanufactured or recycled toner cartridge helps to reduce the utilization of virgin materials. Almost 97% of all the parts of the printer cartridges can be reused or recycled, leading to the conservation of precious natural resources.
It is estimated that recycling brother printer cartridges manufactured every year will save up to four million cubic feet of landfill space.
Why should you recycle or reuse toner cartridge?
It helps to decrease harmful emission of the greenhouse gases that is augmenting the process of global warming across the world.
World energy resources are saved when using recycled toner cartridge. With a minimal production process, it is possible to save a vast amount of energy and utilize it in a better way.
As cartridges take years to break down, recycling them and re-using them will save the planet for future generations and make it a better place to live.
To help reduce the negative impact of the millions of cartridges that are discarded every year, recycling empty cartridges can help support sustainable development. Not only it will help to cut down expenditure on cartridges such as Panasonic toner cartridges and Toshiba toner cartridge , but will also help to save world’s limited natural resources.
Do you know the importance of toner cartridge and toner for printers? If you don’t know, look through this article ,and then you will understand that.Frequently used by the printer users know that ink cartridges and cartridges are essential for printing supplies. If so, then we need to briefly understand the relationship between the cartridge and laser printer, we can first look at the working principle of laser printer! To black and white laser printer works, for example, when the computer through the cable to send data to the printer, the printer will first receive the data temporarily stored in the cache, when receiving a complete data and then sent to the printer's processor, The data is processed into a signal group of similar data tables that can drive the print engine action. For laser printers, these signal sets are a set of pulse signals that drive the laser head to work.
Well, the laser printer began to work, in fact, its core technology is the electronic imaging technology, this technology combines the principles of imaging and electronics to generate images, one of the core components is a photosensitive drum. The laser light emitted by the laser emitter is irradiated on a prismatic mirror. As the mirror rotates, the light is swept from one end of the drum to the other end (through a variety of focusing lenses, so that the light that scans the surface of the drum Point is very small), the drum to 1/300 inch or 1/600 inch step rotation, scanning and then line in the next line. In fact, the toner cartridge is a surface coated with organic materials, the cylinder, in advance with a charge, when there is light to the radiation, the site will be the resistance of the reaction. The computer sends the data signal to control the laser emission, scanning the drum surface of the light constantly changing, so there will be some places by the irradiation, the resistance becomes smaller, the charge disappears, and some places have not been exposed to light, still retain Charge, and finally, the surface of the drum to form a charge by the composition of the latent image.
How does the latent image become a true print image? Toner is a very critical role, the ink and toner is essentially a charge of fine plastic particles, the charge and the drum on the surface of the opposite polarity of the charge, when the charge with the drum surface through the ink roller, the charge Parts on the adsorption of toner particles, latent image becomes a real image. While the drum is rotating, another set of transmission systems feeds the printing paper with the same polarity but much stronger charge as the drum surface, and the paper passes through the toner cartridge with toner and the toner on the drum surface is attracted To the top of the paper, the image is formed on the surface of the paper. At this point, the toner cartridge and the printer are simply joined together by the attraction of the charge. Before the printing paper is sent out of the printer, the high-temperature heating, the plastic toner is melted and solidified on the surface of the paper during the cooling process.
After the toner is attached to the paper, the drum surface continues to rotate, passes through a cleaner, and removes the remaining toner in order to enter the next printing cycle. Visible, in this process the drum occupies a very important position.
In fact, the cartridge is the most critical component of the laser printer. Because it not only determines the quality of print quality, but also determines the cost of printing. This is because in the laser printer, more than 70% of the imaging components are concentrated in the toner cartridge, the print quality is actually a good or bad in fact determined by the cartridge. And the cartridge is part of the printer consumables, the use of a period of time and to achieve a certain number of sheets need to be replaced, so choose the laser printer for the drum there are many knowledge.
Do you know the importance of toner cartridge and toner for printers? If you don’t know, look through this article ,and then you will understand that.Frequently used by the printer users know that ink cartridges and cartridges are essential for printing supplies. If so, then we need to briefly understand the relationship between the cartridge and laser printer, we can first look at the working principle of laser printer! To black and white laser printer works, for example, when the computer through the cable to send data to the printer, the printer will first receive the data temporarily stored in the cache, when receiving a complete data and then sent to the printer's processor, The data is processed into a signal group of similar data tables that can drive the print engine action. For laser printers, these signal sets are a set of pulse signals that drive the laser head to work.
Well, the laser printer began to work, in fact, its core technology is the electronic imaging technology, this technology combines the principles of imaging and electronics to generate images, one of the core components is a photosensitive drum. The laser light emitted by the laser emitter is irradiated on a prismatic mirror. As the mirror rotates, the light is swept from one end of the drum to the other end (through a variety of focusing lenses, so that the light that scans the surface of the drum Point is very small), the drum to 1/300 inch or 1/600 inch step rotation, scanning and then line in the next line. In fact, the toner cartridge is a surface coated with organic materials, the cylinder, in advance with a charge, when there is light to the radiation, the site will be the resistance of the reaction. The computer sends the data signal to control the laser emission, scanning the drum surface of the light constantly changing, so there will be some places by the irradiation, the resistance becomes smaller, the charge disappears, and some places have not been exposed to light, still retain Charge, and finally, the surface of the drum to form a charge by the composition of the latent image.
How does the latent image become a true print image? Toner is a very critical role, the ink and toner is essentially a charge of fine plastic particles, the charge and the drum on the surface of the opposite polarity of the charge, when the charge with the drum surface through the ink roller, the charge Parts on the adsorption of toner particles, latent image becomes a real image. While the drum is rotating, another set of transmission systems feeds the printing paper with the same polarity but much stronger charge as the drum surface, and the paper passes through the toner cartridge with toner and the toner on the drum surface is attracted To the top of the paper, the image is formed on the surface of the paper. At this point, the toner cartridge and the printer are simply joined together by the attraction of the charge. Before the printing paper is sent out of the printer, the high-temperature heating, the plastic toner is melted and solidified on the surface of the paper during the cooling process.
After the toner is attached to the paper, the drum surface continues to rotate, passes through a cleaner, and removes the remaining toner in order to enter the next printing cycle. Visible, in this process the drum occupies a very important position.
In fact, the cartridge is the most critical component of the laser printer. Because it not only determines the quality of print quality, but also determines the cost of printing. This is because in the laser printer, more than 70% of the imaging components are concentrated in the toner cartridge, the print quality is actually a good or bad in fact determined by the cartridge. And the cartridge is part of the printer consumables, the use of a period of time and to achieve a certain number of sheets need to be replaced, so choose the laser printer for the drum there are many knowledge.
HP printer cartridges can be divided into: one, two-in-one and three-body. One type of toner cartridge contains the consumable parts, especially the photosensitive drum, the magnetic roller is very easy to damage, in the disassembly process to be particularly careful. Integral cartridge in the disassembly process need to pay attention to:
First, when the printer cartridge is used in the machine, the drum, the charging roller and the magnet roller are rotated. After assembling these parts, push the gears to check whether they can be rotated flexibly. When the cartridge is finished, push the drum gear again in the direction of normal rotation of the drum to ensure that the drum can be rotated flexibly before the printer cartridge can be dropped, otherwise it will damage the machine.
Second, the positioning problem: each part has its own fixed position, by spring or screw positioning, and powder silo and waste silo two parts by plastic clip, screw or connecting shaft positioning. Assembly parts must be installed in place, so that the normal box to the machine.
Third, the electrical contact: all the printer cartridge in the photosensitive drum, magnetic roller, charging roller has a mechanical contact with the machine, in the assembly to pay attention to the electrical contact at the clean and connected.
Fourth, the magnetic roller: magnetic roller black coating is the most easy to scratch, the magnetic roller is composed of aluminum and magnetic core, due to the role of the core, some small metal parts are easily adsorbed to the surface of the magnet, In the relative movement of the process, the magnetic sleeve coating will be crossed off. Also in the folding process, the magnetic roller is also easy to be adsorbed to the surrounding metal parts, resulting in accidental coating damage. The absence of a black coating creates a lack of text or pattern on the print. So the disassembly, the magnetic roller to stabilize, can not be placed with the room, to place away from other metal parts, to avoid hard bruises.
Fifth, the photosensitive drum: photosensitive drum surface coating can easily be bumped, scratched, and vulnerable to light damage. Improper handling is likely to make a good photosensitive drum in the instant combination of its normal life, so in the folding process, not only to avoid direct sunlight, but also to avoid prolonged exposure to fluorescent light, in addition to yellow light The drum will be damaged. It is forbidden to touch the surface of the drum in a hard object, and it is forbidden to touch the print area of the drum directly by hand so as to avoid perspiration and oil pollution.
We czwartek, 2 maja, na wileńskiej starówce na prośbę Związku Zawodowego Przewodników i Pilotów „Solidarumas” Państwowa Inspekcja Pracy przeprowadziła...
W pierwszą niedzielę maja na Litwie obchodzony jest Dzień Matki. Prezydent Gitanas Nausėda i pierwsza dama Diana Nausėdienė złożyli z tej okazji wszystkim...
Wraz z wyborami prezydenckimi, które odbędą się na Litwie 12 maja, odbędzie się też referendum w sprawie podwójnego obywatelstwa. Poprzedza je kampania...
„Prosimy o dalszą modlitwę za udręczoną Ukrainę. Tak wiele cierpienia, a także za Palestynę i Izrael, aby zapanował pokój. Aby dialog między nimi został...
Publikacje wyrażają jedynie poglądy autorów i nie mogą być utożsamiane z oficjalnym stanowiskiem Kancelarii Prezesa Rady Ministrów i Fundacji „Pomoc Polakom na Wschodzie"